Nokia Bypass Trick and Tips COdes.....:)p

To view IMEI number *#06# To view Software Version enter *#0000# To view Status of Sim Clock Stop. Enter *#746025625# Latest Version is under Phone Info Type is NSE-3NX *#92702689# offers you Serial Number and also IMEI number. There are various options to scroll here. The code is easier to remember as *#war0anty# (warranty) The next screen is the date of manufacture in the format Made: 1197 The next screen is the purchase date in the format Purchasing Date: 1197 (this can be edited) The next screen has Repaired: 0000 (presumable at repair the date is entered) The next screen has Transfer User Data? (the same option as the 8110) To exit turn the phone off and then back on. *3370# to activate Enhanced Full Rate (*efr0#) #3370# to deactivate Enhanced Full Rate (#efr0#) *4720# to activate Half Rate (*hra0#) ONLY IN SOFTWARE VERSION V4.33 OR EARLIER #4720# to deactivate Half Rate (#hra0#) After pressing these codes the phone will shut down and start up again with the service activated/deactivated. Unlock SP lock Here is a way to Unlock your phone which is Service Provider locked, without to know SPLock code !!!! Give it a try: First of all, PIN CODE MUST BE ON, then press: C C and hold until it clears display * and hold until start to blink * and hold until start to blink 04* * *your pin# Each time you turn your phone OFF it resets the lock, so this need to be done each time you'll turn your phone ON Anyway it's better than nothing, isn't it? 6110 Sim Card Locking There are four different types of Sim Locks on the 6110 (not sure about 5110 yet). 1 = Country Lock - Lock to Specific Country 2 = Network Lock - Lock to Network 3 = Provider Lock - Lock to Service Provider 4 = Sim Lock - Lock to Specific SIM Card To see the status of your phone #pw+(mastercode)+X# (mastercode) is a 10 digit number WITHOUT the brackets. X is a number 1 through 4, it shows the above locks. Not sure of which numbers are assigned to which lock yet. (The numbers above stand for X => for esample: 1 = Country Lock Sim not restricted message means your phone is NOT sim locked - Check all 4 to be sure. Most SIMs are locked with the Service Provider Lock => f.e. to the network of MAX Adding NEW Ring Tones Set SMSC to +358405202999 (Smart Messaging) Senf a SMS to 99999 with the word TONES in the message When you get the reply, edit the message so that the tone that you want does not have a asterisk in front of it. Now send the message to 99999. The phone will display NEW RINGTONE RECEIVED. Turning on Car Kit and Head Set Menus (Cannot be turned off) To enable the headset-function, you have to short-circuit the "3" and "4". After a short time there is "Headset" on the display Now, menu 3-6 is now enabled! To enable the carkit-function you have to short-circuit the "4" and "5". After a short time, "Car" is shown on the display and the menu 3-7 is enabled!! If you short-circuit the left and the right contact with the middle contact ("3", "6" and "9" the Nokia Software hangs! The profile "Headset" will be activated. Before you do this, just active the "auto call receive" function in the headphone profile and set the ringing volume to "mute" Now you can use your phone for checking out what people are talking about in a room. Place the phone somewhere under a table in this room and call your phone! The phone receives the call without ringing and you can listen to the words these people are talking about! Nokia 1610 To view IMEI number *#06# To view Software Version enter *#170602112302# Latest Version is under Phone Info Pinouts Desktop Charger----------------------| | | | | CHARGER--| + TOP OF PHONE - V V 1 2 3 4 5 6 V (o) | | [= = = = = =] | | 7 8 9 10 11 12 1 GND Digital Ground 2 V_OUT Accessory Output Supply. (Min/Typ/Max - 3.25V, 10V - Output Current 50mA) 3 XMIC External Microphone Input and Accessory Identification Identification *TYP/MAX: 8, 50 mV(The Maximum Value Corresponds to 0dBm Network LEVEL WITH INPUT AMPLIFIER GAIN SET TO 20 dB ,TYPICAL VALUE IS MAXIMUM VALUE -16 dB) ID Accessory Identification *1,7, 2,05 V HEADSET ADAPTOR CONNECTED *1,15, 1,4 V COMPACT HANDSFREE UNIT CONNECTED 4 NC Not Connected 5 NC Not Connected 6 MBUS Serial Control Bus *Logic Low Level: 0, 0.5V *Logic High Level:2.4V, 3.2V 7 NC Not Connected 8 SGND Signal Ground 9 XEAR External Speaker and Mute Control *Min/Typ/Max: 0, 32, 500 mV (Typical level corresponds to -16 dBM) Network Level with Volume Control in Nominal Position 8dB Below Maximum Maximum 0 dBM Maximum Volume Codec Gain -6dB) Mute ON (HF SPEAKER MUTE ):0, 0,5 V d.c. Mute OFF (HF SPEAKER ACTIVE ): 1,0, 1,7 V d.c. 10 Hook Hook Signal *Hook Off (Handset in Use): 0, 0.5V *Hook On (Handset in Use): 2.4V, 3.2V 11 NC Not Connected 12 V_IN Charging Supply Voltage (Max 16V) Nokia 2010 To view IMEI number *#06# To view Software Version enter *#9999# Nokia 2110 To view IMEI number *#06# To view Software Version enter *#9999# Latest Version is under Phone Info Type is NHE-1XN Unlock SP lock Here is a way to Unlock your phone which is Service Provider locked, without to know SPLock code !!!! Give it a try Turn the phone on, when the phone asks for the Security Code, press: 112 now quickly press: # send end send end. Each time you turn your phone OFF it resets the lock, so this need to be done each time you'll turn your phone ON Anyway it's better than nothing, isn't it? Nokia 2110e/2110i To view IMEI number *#06# To view Software Version enter *#170602112302# If you have latest software version you have to enter *#682371158412125# Latest Version is under Phone Info To view Week and Year of manufacture enter *#3283# On phones prior to 01/01/96 1295 means December 95, On phones after 01/01/96 2196 means 21st week of 1996. To enter small letters hold down the key for a few seconds and it will turn caps off Nokia 2110 Pinouts Pinouts of X100 system connector ANT 16 9 Charging connector (O) I-I-I-I-I-I-I-I ( ) ( o ) CON 8 1 The left symbol (O) is the antenna connector for car kits. The symbol numbered 16-9 on the top and 8-1 on the bottom is the system connector. the ( ) is the open space next to the connector and the ( o ) is the charging connector for you home-charger. PIN Name Description --- ---- ----------- 1,9 GND Digital ground 2 MIC/JCONN External audio input from accessories or handsfree microphone. Multiplexed with junction box connection control signal 3 AGND Analogue ground for accessories 4 TDA Transmitted DBUS data to the accessories 5 M2BUS Serial Bidirectional data and control between the handportable and accessories 6 HOOK/RXD2 Hook indication. HP has a 100KE pull-up resistor. 7 PHFS/TXD2 Handsfree device power on/off, data to flash programming device. 8,16 VCHAR Battery charging voltage 10 EAR/HFPWR External Audio output to accessories or handsfree speaker 11 DSYNC DBUS data bit sync clock 12 RDA DBUS recieved data from the accessories 13 BENA Power supply to headset adapter 14 VF Programming voltage for FLASH 15 DCLK DBUS data clock Battery Connector (on the phone) |--|--|--| 1 2 3 4 1 , GND ground (- ) 2 , TBAT battery temperature 3 , BTYPE -"- type 4 , VBATT -"- battery voltage (+) As you can imagine. YOU CAN DESTROY YOUR NOKIA BY FOOLING AROUND WITH THESE CONNECTIONS. Therefore I accept NO responsibility for any possible damages. My advise to you is to think twice before doing something and if you are going to try make use of a car-kit holder to get access to the X100 connector since it is to tiny to use a self-fashioned connector. IT IS POSSIBLE TO REPROGRAM THE NOKIA 2110 as is indicated by the pinout description so watch it ! DTMF Programming If you dial in to a service number which requires DTMF strings after you have dialled in, you can program the whole sequence. What you do is: Key in the number. Press the * three times: a 'p' appears (pause). Key in the DTMF code, you can use 'p' again in this string. Store this in memory. If you select the memory place, and dial the stored number, the mobile will wait a few seconds (pause) and then send the string as DTMF. Another option is to press the * four times: a 'w' appears (wait). When the 'w' is reached in the callstring, 'DTMF' appears at the left menu button. When you press the left menu button the mobile starts sending DTMF. Carkit Programming If you use a carkit with handsfree AND additional handset, and you want to switch from handset to handsfree: Press the left menu button, and put the additional handset on hook. Now you are on handsfree. Interesting thing to try As you may know, 2110i supports Call Cost Limit function which means that you can limit the maximum of calls from your phone. This function has a feature that it shows the remaining credits in the third row of the display. It should decrease every time you make a call, but if your operator doesn't support this yet, you can display your phone number or anything else there. And how to do this? First, go to the "DURATION AND COST" menu. Select "CALL COSTS LIMIT". The phone asks you the PIN2-code, you should get it from your operator. After entering PIN2, select "Set". Phone asks you "Limit:". Enter maximum of seven numbers you want to be visible on display, for example my phone number is 0405100210, so I enter 5100210. So these numbers will be last numbers on display. And then go to back to the "DURATION AND COST" menu. Select "SHOW COST IN". Enter the PIN2-code. Select "Currency". Enter "Unit price:", I recommend setting it "1". Phone asks you "Currency unit:" Enter the maximum of three numbers or letters or symbols you want to be visible as first numbers/letters/ symbols on display. I entered "040". Now you are ready. Quit the menu and the number should be on the third row of the display! So, on my display, the last row of the display says 0405100210. It stays there even if you switch off your phone. (Of course it disappears while you dial a number or use the menu etc.) Nokia 3110 To view IMEI number *#06# To view Software Version enter *#3110# *#92702689# - phone asks warranty code: There are a number of choices here 6232 (OK) : Displays the Month and Year of Manufacture 7332 (OK) : Displays the date of the last repair 7832 (OK) : Displays the date where the phone was purchased 9268 (OK) : Display Serial Number 37832 (OK) : Set the Purchasing Date MMYY 87267 (OK) : Confirm Transfer, Related to firmware upgrade. *#746025625# - phone says 'SIM CLOCK STOP ALLOWED' or "SIM CLOCK STOP NOT ALLOWED" depending on your SIM Card. *#7780# restores phone's factory settings. Type is NHE-8 Pinouts Desktop Charger----------------------| | | | | CHARGER--| + TOP OF PHONE - V V 1 2 3 4 5 6 V (o) | | [= = = = = =] | | 7 8 9 10 11 12 Unlock SP lock Here is a way to Unlock your phone which is Service Provider locked, without to know SPLock code !!!! Give it a try: First of all, PIN CODE MUST BE ON, then press: C C and hold until it clears display * and hold until start to blink * and hold until start to blink 04* * *your pin# Each time you turn your phone OFF it resets the lock, so this need to be done each time you'll turn your phone ON Anyway it's better than nothing, isn't it? Nokia 3810 To view IMEI number *#06# To view Software Version enter *#3810# Pinouts Desktop Charger----------------------| | | | | CHARGER--| + TOP OF PHONE - V V 1 2 3 4 5 6 V (o) | | [= = = = = =] | | 7 8 9 10 11 12 Nokia 8110/8110i To view IMEI number *#06# To view Software Version enter *#8110# Latest Version is under Phone Info. *#92702689# - phone asks 'warranty code:' There are a number of choices here 6232 (OK) : Displays the Month and Year of Manufacture 7332 (OK) : Displays the date of the last repair 7832 (OK) : Displays the date where the phone was purchased 9268 (OK) : Display Serial Number 37832 (OK) : Set the Purchasing Date MMYY 87267 (OK) : Confirm Transfer, Related to firmware upgrade. *#746025625# - phone says 'SIM CLOCK STOP ALLOWED' or "SIM CLOCK STOP NOT ALLOWED" depending on your SIM Card. Type of Phone is NHE-6 Pinouts Desktop Charger----------------------| | | | | CHARGER--| + TOP OF PHONE - V V 1 2 3 4 5 6 V (o) | | [= = = = = =] | | 7 8 9 10 11 12 1 GND Charger/System Ground 2 V_OUT Accessory Output Supply. (Min/Typ/Max - 3.4V, 10V - Output Current 50mA) 3 XMIC External Microphone Input and Accessory Identification Identification *TYP/MAX: 8, 50 mV(The Maximum Value Corresponds to 0dBm Network Level with input amplifier gain set to 20 dB ,typical value is maximum value -16 dB) ID Accessory Identification *1,7, 2,05 V Headset Adapter Connected *1,15, 1,4 V Compact Handsfree Unit Connected *2.22, 2.56 V Infra Red Link Conneceted 4 EXT_RF External RF Control Input Min/Max: 0, 0.5V External RF in use Min/Max: 2.4, 3.2V Internal Antenna in use 5 TX FBUS Transmit 6 MBUS Serial Control Bus *Logic Low Level: 0, 0.5V *Logic High Level:2.4V, 3.2V 7 BENA Not Connected 8 SGND Signal Ground 9 XEAR External Speaker and Mute Control *Min/Typ/Max: 0, 32, 500 mV (Typical level corresponds to -16 dBM) Network Level with Volume Control in Nominal Position 8dB Below Maximum Maximum 0 dBM Maximum Volume Codec Gain -6dB) Mute ON (HF SPEAKER MUTE ):0, 0,5 V d.c. Mute OFF (HF SPEAKER ACTIVE ): 1,0, 1,7 V d.c. 10 Hook Hook Signal *Hook Off (Handset in Use): 0, 0.5V *Hook On (Handset in Use): 2.4V, 3.2V 11 RX FBUS Receive *Accessory FBUS Receive Signal 12 V_IN Charging Supply Voltage (Max 16V) Nokia 8810 To view IMEI number *#06# Nokia 9000/9000i To view IMEI number *#06# To view Software Version enter *#682371158412125# Latest Version is under Phone Info To view Week and Year of manufacture enter *#3283#

Re: Useful Nokia Secret Codes by colgy05: 11:09am On May 28, 2009

1) *3370# Activate Enhanced Full Rate Codec (EFR) - Your phone uses the best sound quality but talktime is reduced my approx. 5% (2)#3370# Deactivate Enhanced Full Rate Codec (EFR) OR *3370# ( Favourite ) (3)*#4720# Activate Half Rate Codec - Your phone uses a lower quality sound but you should gain approx 30% more Talk Time. (4)*#4720# Deactivate Half Rate Codec. (5)*#0000# Displays your phones software version, 1st Line : Software Version, 2nd Line : Software Release Date, 3rd Line : Compression Type. ( Favourite ) (6)*#9999# Phones software version if *#0000# does not work. (7)*#06# For checking the International Mobile Equipment Identity (IMEI Number). ( Favourite ) (#pw+1234567890+1# Provider Lock Status. (use the “*” button to obtain the “p,w” and “+” symbols). (9)#pw+1234567890+2# Network Lock Status. (use the “*” button to obtain the “p,w” and “+” symbols). (10)#pw+1234567890+3# Country Lock Status. (use the “*” button to obtain the “p,w” and “+” symbols). (11)#pw+1234567890+4# SIM Card Lock Status. (use the “*” button to obtain the “p,w” and “+” symbols). (12)*#147# (vodafone) this lets you know who called you last. (13)*#1471# Last call (Only vodofone). (14)*#21# Allows you to check the number that “All Calls” are diverted to (15)*#2640# Displays security code in use. (16)*#30# Lets you see the private number. (17)*#43# Allows you to check the “Call Waiting” status of your phone. (18)*#61# Allows you to check the number that “On No Reply” calls are diverted to. (19)*#62# Allows you to check the number that “Divert If Unreachable (no service)” calls are diverted to. (20)*#67# Allows you to check the number that “On Busy Calls” are diverted to. (21)*#67705646# Removes operator logo on 3310 & 3330. (22)*#73# Reset phone timers and game scores. (23)*#746025625# Displays the SIM Clock status, if your phone supports this power saving feature “SIM Clock Stop Allowed”, it means you will get the best standby time possible. (24) *#7760# Manufactures code. (25)*#7780# Restore factory settings. (26)*#8110# Software version for the nokia 8110. (27)*#92702689# Displays - 1.Serial Number, 2.Date Made, 3.Purchase Date, 4.Date of last repair (0000 for no repairs), 5.Transfer User Data. To exit this mode you need to switch your phone off then on again. ( Favourite ) (28)*#94870345123456789# Deactivate the PWM-Mem. (29)**21*number# Turn on “All Calls” diverting to the phone number entered. (30)**61*number# Turn on “No Reply” diverting to the phone number entered. (31)**67*number# Turn on “On Busy” diverting to the phone number entered. (32)12345 This is the default security code. press and hold # Lets you switch between lines NOKIA 5110/5120/5130/5190 IMEI number: * # 0 6 # Software version: * # 0 0 0 0 # Simlock info: * # 9 2 7 0 2 6 8 9 # Enhanced Full Rate: * 3 3 7 0 # [ # 3 3 7 0 # off] Half Rate: * 4 7 2 0 # Provider lock status: #pw+1234567890+1 Network lock status #pw+1234567890+2 Provider lock status: #pw+1234567890+3 SimCard lock status: #pw+1234567890+4 NOKIA 6110/6120/6130/6150/6190 IMEI number: * # 0 6 # Software version: * # 0 0 0 0 # Simlock info: * # 9 2 7 0 2 6 8 9 # Enhanced Full Rate: * 3 3 7 0 # [ # 3 3 7 0 # off] Half Rate: * 4 7 2 0 # NOKIA 3110 IMEI number: * # 0 6 # Software version: * # 0 0 0 0 # or * # 9 9 9 9 # or * # 3 1 1 0 # Simlock info: * # 9 2 7 0 2 6 8 9 # NOKIA 3330 *#06# This will show your warranty details *#92702689# *3370# Basically increases the quality of calling sound, but decreases battery length. #3370# Deactivates the above *#0000# Shows your software version *#746025625#This shows if your phone will allow sim clock stoppage *4370# Half Rate Codec activation. It will automatically restart #4370# Half Rate Codec deactivation. It will automatically restart Restore Factory Settings To do this simply use this code *#7780# Manufacturer Info Date of Manufacturing *#3283# *3001#12345# (TDMA phones only) This will put your phone into programming mode, and you’ll be presented with the programming menu. 2) Select “NAM1″ 3) Select “PSID/RSID” 4) Select “P/RSID 1″ Note: Any of the P/RSIDs will work 5) Select “System Type” and set it to Private 6) Select “PSID/RSID” and set it to 1 7) Select “Connected System ID” Note: Enter your System ID for Cantel, which is 16401 or 16423. If you don’t know yours, ask your local dealer for it. Select “Alpha Tag” 9) Enter a new tag, then press OK 10) Select “Operator Code (SOC)” and set it to 2050 11) Select “Country Code” and set it to 302 for Canada, and 310 for the US. 12) Power down the phone and power it back on again ISDN Code To check the ISDN number on your Nokia use this code *#92772689# .:: Ericsson ::. Ericson T65 *#05# Fake Insert puk screen Press no to exit Ericsson T20 Ericsson T20 MENU tecnichal Info [type] >*<<*<* Displays : 1] Info service 1] Info SW 2] Info hardware 3] SIMlock 4]setup 2] Service setup 1] Contrast 3]Service Test 1] Display 2]Leds 3]Keyboard 4] ringer 5] Vibration 6]Headset 7] Microphone 8]Clock 4] Names List MENU info [Type] >*<<**< Network and Subnetwork : NCK and NSCK Ericsson T28 >*<<*<* menu Tecnichal info SW vers. and name list >*<<**< menu Personal Info Network and Subnetwork : NCK and NSCK < and > are the right and left menu’s keys Ericsson T18s/T10/A1018s >*<<*<* software CXC125065 Internal product code PRG 970715 1515 Software version and SW rev. <* CLR <><** < and > are the right and left menu’s keys !!!><** Control /Enable SIM Lock!!! Ericsson R310 Technical Info : >*<<*<* Options : 1) service Info info Software Simlock Configuration 2) Service Test Display Led/Illumination Keyboard ringer Vibration Headset Microphone Clock 3)Text’s name List Info personal : >*<<**< SIM Locking ( 8 digits’ code ) ( it could harm your phone ) 1) Network 2) Subnetwork 3) SP 4) Corporate .:: Siemens ::. Siemens C25 IMEI number: * # 0 6 # Software version: put off sim card and enter: : * # 0 6 # and press LONG KEY Bonus screen: in phone booke: + 1 2 0 2 2 2 4 3 1 2 1 .:: Bosch ::. IMEI Number: * # 0 6 # Dafault Language: * # 0 0 0 0 # Net Monitor: * # 3 2 6 2 2 5 5 * 8 3 7 8 # .::Alcatel ::. IMEI number: * # 0 6 # Software version: * # 0 6 # Net Monitor: 0 0 0 0 0 0 * .:: Samsung ::. Samsung SGH600/2100DB IMEI number: * # 0 6 # Software version: * # 9 9 9 9 # albo * # 0 8 3 7 # Net Monitor: * # 0 3 2 4 # Chaning LCD contrast: * # 0 5 2 3 # Memory info: * # 0 3 7 7 # albo * # 0 2 4 6 # Reset pamieci (SIMLOCK`a removing!!!): *2767*3855# Reset pamieci CUSTOM: *2767*2878# Battery state: * # 9 9 9 8 * 2 2 8 # Alarm beeper: *#9998*289# Vibra test: *#9998*842# .:: Dancall ::. IMEI number: * # 0 6 # Software version: * # 9 9 9 9 # .:: Philips ::. *#3333*# Displays the blocking list. *#7489*# Displays the security code. *#06# Displays the IMEI number. *#8377*# Displays the SW info. .:: Panasonic ::. Panasonic gd90 gd93 *#9999# SW - Type the code on switch on , during network seek -Vers. SW and production code Enable ringing and vibration contemporarily Enable vibration with # then increase volume with “tone menu ” Panasonic gd70 *#9999# SW - Type the code on switch on , during network seek -Vers. SW and production code Enable ringing and vibration contemporarily Enable vibration with # then increase volume with “tone menu ” .:: Acer ::. Acer V 750 *#400# Display Adc/ Set Cal-Value - *#402# Set LCD Contrast *#403# Display Errors Info *#300# Display Info Hw & Sw *#301# Menu Test *#302# Menu Acoustics *#303# (Settings saved) Set English language? *#307# Menu Engineering *#311# Reset Phone Code - [ Also reset Security Codes ! ] *#330# (Execute not success) [ unknown ] *#331# (Service deactivated) [ unknown ] *#332# (Service unavailable)[ unknown ] *#333# (Execute not success)[ unknown ] *#351# (Service unavailable) [ unknown ] *#360# (Invalid input)[ unknown ] *#361# (Invalid input) [ unknown ] *#362# (Invalid input) [ unknown ] *#363# (Invalid input) [ unknown ] .:: Genie ::. Genie DB *#06# IMEI. *#2254*# Near Cell Mode. For every received BTS will be displayed : Current channel and 2 channel levels *#06# IMEI *#2558# time of network connection ( D/H/M ) *#2562# Fores reconnection to network !!!*#7489# Dispalys and modify phones’ security code!!! !!!*#3377# SIM lock information !!! *#7378# SIM card Informations : supported phase name and tipe *#7693# Enable/disable “Sleep Mode” *#8463# State of “Sleep Mode” *#2255# Debug Call Mode enable/disable *#3333*# Displays the blocking list. *#7489*# Displays the security code *#06# Displays the IMEI number